Search Results

Laser welding of the magnesium-bearing AA5xxx aluminum alloys is often beset by keyhole instability, especially in the lap through joint configuration. This phenomenon is characterized by periodic collapse of the keyhole leaving large voids in the weld zone. In addition, the top surface can exhibit undercut and roughness. In full penetration welds, keyhole instability can also produce a spikey root and severe top surface concavity. These discontinuities could prevent a weld from achieving engineering specification compliance, pose a craftsmanship concern, or reduce the strength and fatigue performance of the weld. In the case of a full penetration weld, a spikey root could compromise part fit-up and corrosion protection, or damage adjacent sheet metal, wiring, interior components, or trim.

This paper analyzes the use of an ammonia sensor for feedback control in diesel exhaust systems. We build our case around the specific example of the heavy duty transient cycle, and an exhaust system with an SCR catalyst, a single urea injector and an upstream and downstream NOx sensor. A key component in our analysis is the inclusion of the tolerance of the ammonia sensor. We show that with the current understanding of the sensor tolerance, the ammonia sensor has limited benefit for controls.

By utilizing the vehicle to infrastructure communication, the conventional Green Light Optimized Speed Advisory (GLOSA) applications give speed advisory range for drivers to travel to pass at the green light. However, these systems do not consider the traffic between the ego vehicle and the traffic light location, resulting in inaccurate speed advisories. Therefore, the driver needs to intuitively adjust the vehicle's speed to pass at the green light and avoid traffic in these scenarios. Furthermore, inaccurate speed advisories may result in unnecessary acceleration and deceleration, resulting in poor fuel efficiency and comfort. To address these shortcomings of conventional GLOSA, in this study, we proposed the utilization of collaborative perception messages shared by smart infrastructures to create an enhanced speed advisory for the connected vehicle drivers and automated vehicles.

Multiple approaches have been created to enhance intra-vehicle communications security over the past three decades since the introduction of the Controller Area Network (CAN) protocol. The twin pair differential-mode communications bus is tremendously robust in the face of interference, yet physical access to the bus offers a variety of potential attack vectors whereby false messages and/or denial of service are achievable. This paper evaluates extensions of a Physical-layer (PHY) common-mode watermark-based authentication technique recently developed to improve authentication on the CAN bus by considering the watermark as a side-channel communications means for high value information. We also propose and analyze higher layer algorithms, with benefits and pitfalls, for employing the watermark as a physical-layer firewall.

A novel laser-absorption gas sensing apparaOn-vehicle Testing at VERtus capable of measuring NO directly within vehicle exhaust was developed and tested. The sensor design was enabled by key advances in the construction of optical probes that are sufficiently compact for deployment in real-world exhaust systems and can survive the harsh, high-temperature, and strongly vibrating environment typical of exhaust streams. Prototype test campaigns were conducted at high-temperature flow facilities intended to simulate exhaust gas conditions and within the exhaust of vehicles mounted on a chassis dynamometer. Results from these tests demonstrated that the sensor prototype is fundamentally free of cross-interference with competing species in the exhaust stream, can achieve a 1 ppmv NO detection limit, and can be operated across the full range of thermodynamic conditions expected for typical vehicle exhausts.

As electric vehicles are becoming increasingly popular and necessary for the future mobility needs of civilization, further effort is continually made to improve the efficiency, cost, and safety of the lithium-ion battery packs that power these vehicles. To facilitate these goals, this paper introduces a data driven model to predict a distribution of surface temperatures for a lithium-ion battery pack: a long short-term memory (LSTM) neural network. The LSTM model is trained and validated with lithium-ion cells electrically connected to form a battery pack. Voltage, current, state of charge (SOC), and cell surface temperature from two arrays are used as inputs from a wide range of high and low temperature drive cycles. Additionally, ambient temperature is added as an input to the LSTM model.

In this paper, we present an end-to-end real-time detection and collision avoidance framework in an autonomous vehicle using a monocular RGB camera. The proposed system is able to run on embedded hardware in the vehicle to perform real-time detection of small objects. RetinaNet architecture with ResNet50 backbone is used to develop the object detection model using RGB images. A quantized version of the object detection inference model is implemented in the vehicle using NVIDIA Jetson AGX Xavier. A geometric method is used to estimate the distance to the detected object which is forwarded to a MicroAutoBox device that implements the control system of the vehicle and is responsible for maneuvering around the detected objects. The pipeline is implemented on a passenger vehicle and demonstrated in challenging conditions using different obstacles on a predefined set of waypoints.

Most of the applications of magnesium in lightweighting commercial cars and trucks are die castings rather than sheet metal, and automotive applications of magnesium sheet have typically been experimental or low-volume serial production. The overarching objective of this collaborative research project organized by the United States Automotive Materials Partnership (USAMP) was to develop new low-cost magnesium alloys, and demonstrate warm-stamping of magnesium sheet inner and outer door panels for a 2013 MY Ford Fusion at a fully accounted integrated component cost increase over conventional steel stamped components of no more than $2.50/lb. saved ($5.50/kg saved). The project demonstrated the computational design of new magnesium (Mg) alloys from atomistic levels, cast new experimental alloy ingots and explored thermomechanical rolling processes to produce thin Mg sheet of desired textures.

Studies regarding the automotive communication networks has been a fast-growing subject of research through automotive companies. One of the main issues during a vehicle network prototype development is the necessity of a programmed hardware for gateway modules. The gateway developed by an automotive supplier, usually implemented at an Electronic Control Unit (ECU), is one of the last remaining modules to have a software available because it needs to wait the message list completion of all ECUs prior to set up its own message list and network interfaces. This paper proposes a method to design and test Controlled Area Network (CAN) gateways using Vector CANoe software by developing ways to facilitate a scalable code production in CAPL scripts. Use cases will use gatewayed signals virtually validated prior to software deployment, along with codes proposals and common cases examples.

The automotive industry is passing for a big transformation, due to technologies advance. The electrical technologies are also on a good rising curve, calling the attention of the Original Equipment Manufacturer (OEMs). This scenario generates the demand for a faster method to train their new hired engineers, when compared with usual on the job training. Model in the Loop (MiL) consists in one of the real-time embedded systems test phases, which is developed in a computational environment, performing a mathematical modeling of the system, presenting an interface that allows the visualization of its dynamics and the signals involved. Two powerful software in industry that apply MiL are the Matlab and Simulink. A project involving these applications was proposed for a team of new hired engineers, developing models of several vehicle Electronic Control Units (ECUs), with some scope reduction as an example the functional requirements reduction.

This article aims to analyze the potential economic effects for consumers with the implementation of the Vehicle-to-Grid (V2G) and the Vehicle-to-Home (V2H) networks in Brazil. Nowdays, the usage of both technologies in Brazil are at a regulatory vacuum for both Battery Electric Vehicles (BEVs), Plug-in Hybrid Electric Vehicles (PHEVs) and Hybrid Electric Vehicles (HEVs). Usually, when a legislation lack occurs, the local OEMs adopt IECs (International Electrotechnical Commissions) and/or SAEs (Society of Automotive Engineers) reference international standards, such as SAE J1634 for range test.

NVH problems are often the result of mechanisms that originate through complex interactions between different physical domains (flow, structural/mechanical, control logic, etc.). Parallel-shaft spur gears subject to light torque loading caused by the dynamic pressure fluctuation of the oil used in engine accessory or transmission pump drives are likely to exhibit unusual gear whine associated with higher order meshing harmonics, even when the tooth profile has a high-quality grade finishing. Therefore, accurate integrated models are becoming a requirement to solve modern NVH problems.

The ported shroud casing treatment for turbocharger compressors offers a wider operating flow range, elevated boost pressures at low compressor mass flow rates, and reduced broadband whoosh noise in spark-ignition internal combustion engine applications. However, the casing treatment elevates tonal noise at the blade-pass frequency (BPF). Typical rotational speeds of compressors employed in practice push BPF noise to high frequencies, which then promote multi-dimensional acoustic wave propagation within the compressor ducting. As a result, in-duct acoustic measurements become sensitive to the angular location of pressure transducers on the duct wall. The present work utilizes a steady-flow turbocharger gas stand featuring a unique rotating compressor inlet duct to quantify the variation of noise measured around the duct at different angular positions.

As the automotive industry strives for an increased fuel economy, lightweighting is a key factor and can be realized through composite materials. Composites have better strength-to-weight ratio as compared to metals. In this paper, static and fatigue analysis is performed on an oil pan made of polyamide-6,6 and 50% glass fiber (PA66-GF50). PA66 has a glass transition temperature of 170°C; therefore, it is suitable for automotive applications where the operating range is −40°C to 150°C. Long glass fiber (LGF) composite has an aspect ratio of 30-50 in the oil pan. Fibers break in the molding process but are still considerably longer than with conventionally compounded short glass fiber (SGF) composite, where the aspect ratio of fiber is between 10 and 20. However, the computer-aided engineering (CAE) procedure for life prediction of short glass fiber-reinforced (SGFR) plastic versus LGF-reinforced plastic is the same.

In this paper, a novel methodology of nonlinear control is used, and a passivity-based control of contractive port-controlled Hamiltonian (PCH) systems is applied to a permanent magnet synchronous motor (PMSM). This methodology, also called “tIDA-PBC” (Trajectory Injection and Damping Assignment—Passivity-Based Control), uses passivity-based control of PCH systems “IDA-PBC” and exploits the properties of contractive Hamiltonian systems, resulting in a closed loop with its contractive system desired dynamics, thus obtaining an exponential trajectory tracking without relying on the error coordinates. In this system, a few steps are proposed in order to divide and modularize the methodology so it can be redesigned or reapplied in other systems by the reader. First, we define the model and set the way to solve the “matching equation.” Then the feasible and reference trajectories are obtained.

Researchers and engineers are utilizing big data analytics to draw further insights into transportation systems. Large amounts of data at the individual vehicle trip level are being collected and stored. The true potential of such data is still to be determined. In this paper, we are presenting a data-driven, novel, and intuitive approach to model driver behaviors using microscopic traffic simulation. Our approach utilizes metaheuristic methods to create an analytical tool to assess vehicle performance. Secondly, we show how microscopic simulation run outputs can be post-processed to obtain vehicle and trip level performance metrics. The methodology will form the basis for a data-driven approach to unearthing trip experiences as realized by drivers in the real world. The methodology will contribute to, A.) Using vehicle trajectory traces to identify underlying vehicle maneuver distributions as obtained from real-world driver data, B.)

Exhaust sensors and actuators used in automotive applications are subjected to wide variety of operating ambient conditions , the performance of these actuators is challenging especially at cold ambient operating conditions, active exhaust tuning valves with position sensors are used to adjust the sound levels, or noise, vibration and harshness (NVH) from a control unit within the vehicle that leads to an improved driving experience wherein the driver selects their preferred sound levels. However, the operating behavior is crucially influenced by the characteristics of the drive cycle and ambient temperature. The study in this paper is intended to evaluate the icing formation at the start of drive cycle and at different ambient temperature conditions. The test data were obtained through real road and chassis dyno testing at different ambient conditions.

A cast magnesium AE44 subframe was designed and manufactured for a C Class sedan to reduce weight and improve vehicle fuel economy. Corrosion mitigation strategies were developed to reduce the likelihood of galvanic corrosion. Both a proving ground vehicle corrosion test and a laboratory component corrosion test were conducted. The vehicle test result demonstrated that the corrosion mitigation strategies were effective. They also provided lessons learned on clearance between magnesium and steel components and options to improve the subframe’s corrosion resistance. The magnesium subframe achieved 5 kg (32%) weight reduction from the equivalent steel subframe and met all the required structural performance targets.

A cast magnesium subframe was designed and manufactured for a C Class sedan to reduce weight and improve vehicle fuel economy. The magnesium subframe achieved 5 kg (32%) weight reduction from the equivalent steel subframe and met all the required structural performance targets. All the joints of the magnesium subframe were tested for bolt load retention. The tests were conducted with a temperature profile of 100°C to -30°C designed to investigate the creep behavior of the selected magnesium alloy AE44 under high stress.

As the world searches for ways to reduce humanity’s impact on the environment, the automotive industry looks to extend the viable use of the gasoline engine by improving efficiency. One way to improve engine efficiency is through more effective control. Torque-based control is critical in modern cars and trucks for traction control, stability control, advanced driver assistance systems, and autonomous vehicle systems. Closed loop torque-based engine control systems require feedback signal(s); indicated mean effective pressure (IMEP) is a useful signal but is costly to measure directly with in-cylinder pressure sensors. Previous work has been done in torque and IMEP estimation using crankshaft acceleration and ion sensors, but these systems lack accuracy in some operating ranges and the ability to estimate cycle-cycle variation.